![]() There are limits as to the amount of points you can bypass.ħ. If you don’t know the point number just press NEXT and the keypad will take you through the available choices. ![]() In order to clear the Keypad memory buffer simply enter your code and then press the ESC button and it will clear old events that have restored.Ħ.ěypassing and Un-bypassing can be done using the instructions on #3, when you get to bypass or unbypass it will ask you for your code and then the point number you want to bypass or unbypass. This will tell you the faulted points and problems.ĥ. If the system will not arm up then press the NEXT button and note the message, press the NEXT button again and note all the messages. 3.ğor other functions press MENU then scroll using NEXT and PREV, once you get to a menu item you would like to use press ENTER then the keypad may or may not ask you for your code, if it does enter your code and then press ENTER. Make sure you enter in the door that has a delay programmed. Normally this should be done in the first 30 or 60 seconds whatever your delay time is. 2.ĝisarming is also done by TYPING IN YOUR CODE and pressing enter. Even hanging signs can set the system into alarm. Secure all points on system such as closing doors and verify that no balloons or moving displays are in areas with motion detectors then ARM system by TYPING IN YOUR CODE and pressing enter. You can also get the instruction sheets off of for each product.ĭispatch phone _Īccount #_ 1. You may want to simplify these instructions and post them or put them in a procedure notebook. The D1265 is the new virtual keypad with a touch screen. The D1256 Keypad is a Fire keypad and has very few buttons so employees can view, silence and reset alarms. It does draw more mA current to operate so a new power supply may need to be added if you do more than one. Also the new D1260 keypad which is the ATM style has buttons on the sides to take you to where you want to go faster and it has the users manuals built into it with a large screen. Your system can be customized to turn functions on or off in the keypad menu. An example of this is CMD 47 (Reset) The Bosch systems can be programmed in many ways so the following is a general instruction sheet. The D1255 Keypad allows you to use CMD commands as well that are shortcuts when they are programmed or turned on. When multiple keypads are configured, the thumbnail image from this camera will be included with arm/disarm push notifications.Training for managers – Have your account number and password ready for the dispatchers. Camera - Select the camera that is pointed at the primary keypad.Remote Key - Enter the remote key designated in the Remote Options panel information in the DMP Remote Link (this should be provided by your installer).Account Number - Enter the account number designated in the Communications Path information in the DMP Remote Link (this should be provided by your installer).Will show accountnumber-0 for the panel, accountnumber-1 for the first area, -2, -3 and so on for subsequent configured areas. State - Select Enabled to connect to the panel.IP Address - The IP of the DMP Panel (see the DMP Panel Configuration Requirements section).Name - Identity the panel being connected.In the Intrusion Panel, select Add New Intrusion Panel and complete the fields noted below: Intrusion Panels are used to set up connections to the DMP panel. Manually reconfiguring the panel may be necessary depending on previous configurations. When upgrading the firmware be sure to reset the panel when complete. NOTE: Integration with XR-Series and XT-Series panels requires firmware 171 or greater on the panel. NOTE: Currently, OpenEye supports the XR-Series (XR550, XR150) and XT-Series (XT50, XT30) alarm panels. Enter the Outbound TCP Port (2001 as default).Enter the IP address of the recorder in the Integrator IP Address box.Enter the Incoming TCP Port (2001 as default).To set up an XR series panel, it is necessary to configure the integrator Path in the Remote Options section in the Remote Link software connected to the DMP panel: Setting Up XR Series Panels (for Panels with Versions Less than 192 and Beyond)
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |